national canner #7

spereira · March 21, 2015

I have an old National Canner #7 and I need a sealing ring. My local hardware store sold me a sealing ring ,however the locking pin on the canner prevents the ring from sealing properly.. Do I press the ring down over the pin or do I have the wrong ring?

Steve

**coronabarb** · March 21, 2015

Steve,

I can't answer that. If someone else doesn't chime in, you can try the Oregon St Univ extension website where you can "ask an expert". Nellie usually answers them pretty quickly.

http://extension.oregonstate.edu/com...d-preservation

Worth1 · March 21, 2015

I thought this was yet another tomato variety thread.

Let me do some research.

Worth

Worth1 · March 21, 2015

I'm back it is part number 09907 that you want.
I will post a link to the amazon site.
Read what the folks have to say below the product.
This is the part number that the folks at presto said fit.
http://www.google.com/url?sa=t&rct=j...,d.eXY&cad=rja

Worth

spereira · March 22, 2015

thanks for the help.

dustdevil · March 22, 2015

I think this may help with your problem.

Download this manual and refer to page 14:

http://www.pickyourown.org/canning_e...structions.pdf

Refer to this page for additional sealing ring info:

http://www.pressurecooker-outlet.com/7.htm

Be sure to read questions and reviews by purchasers(feedback). There is info on seal install:

http://www.amazon.com/Presto-Pressur.../dp/B000LL9NY2

spereira · March 22, 2015

thanks for the manuals..the directions say to replace the seal "IN THE COVER"..hmm. I was placing the seal on the body of the canner. I can't see where the seal would go in the lid(cover) unless the groove that would hold the seal was so filled with old gunk. I must be dense because what should be obvious isn't.

whistech · March 22, 2015

Can you post a couple of pictures of the canner and the lid? It would help in solving your canner problem.

dustdevil · March 22, 2015

There may have been a seal design change over the years. I do know that the early ones with wooden handles have a wide pot rim with a very wide seal. Perhaps the more O-ringish seal with grooves is for later models. Compare your canner with the pdf manual I suggested you download. That manual is a copy of the original National #7. Hopefully some clown didn't mix a top of one model with the bottom of another model...I don't know if that's possible, but who knows!

Call Presto customer service if you still can't figure it out.

That's all I've got. Good Luck!

spereira · March 23, 2015

Thanks for everyone's efforts. I don't have a digital camera..going to have to get one.

I did order another seal just in case I got the wrong one the first time.

March 21, 2015	#1
spereira Tomatovillian™ Join Date: Mar 2015 Location: northern MN Posts: 26	national canner #7 I have an old National Canner #7 and I need a sealing ring. My local hardware store sold me a sealing ring ,however the locking pin on the canner prevents the ring from sealing properly.. Do I press the ring down over the pin or do I have the wrong ring? Steve

March 21, 2015	#2
coronabarb Tomatoville® Recipe Keeper Join Date: Jan 2006 Location: Roseburg, Oregon - zone 7 Posts: 2,821	Steve, I can't answer that. If someone else doesn't chime in, you can try the Oregon St Univ extension website where you can "ask an expert". Nellie usually answers them pretty quickly. http://extension.oregonstate.edu/com...d-preservation __________________ Corona~Barb Now an Oregon gal

March 22, 2015	#5
spereira Tomatovillian™ Join Date: Mar 2015 Location: northern MN Posts: 26	thanks thanks for the help.

March 22, 2015	#6
dustdevil Tomatovillian™ Join Date: Jan 2010 Location: WI, USA Zone4 Posts: 1,887	I think this may help with your problem. Download this manual and refer to page 14: http://www.pickyourown.org/canning_e...structions.pdf Refer to this page for additional sealing ring info: http://www.pressurecooker-outlet.com/7.htm Be sure to read questions and reviews by purchasers(feedback). There is info on seal install: http://www.amazon.com/Presto-Pressur.../dp/B000LL9NY2 Last edited by dustdevil; March 22, 2015 at 01:40 PM.

March 21, 2015	#3
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	I thought this was yet another tomato variety thread. Let me do some research. Worth

March 22, 2015	#7
spereira Tomatovillian™ Join Date: Mar 2015 Location: northern MN Posts: 26	read the directions thanks for the manuals..the directions say to replace the seal "IN THE COVER"..hmm. I was placing the seal on the body of the canner. I can't see where the seal would go in the lid(cover) unless the groove that would hold the seal was so filled with old gunk. I must be dense because what should be obvious isn't.

March 22, 2015	#8
whistech Tomatovillian™ Join Date: Aug 2012 Location: Between The Woodlands and Spring, Texas Posts: 553	Can you post a couple of pictures of the canner and the lid? It would help in solving your canner problem.

March 23, 2015	#10
spereira Tomatovillian™ Join Date: Mar 2015 Location: northern MN Posts: 26	Thanks for everyone's efforts. I don't have a digital camera..going to have to get one. I did order another seal just in case I got the wrong one the first time.