Operation Old Pressure Cooker. - Page 14

dmforcier · March 12, 2017

Quote:

Collar on or off?

Collar off, as per Korean FDA regulations.

AlittleSalt · March 12, 2017

Quote:

Originally Posted by Worth1

Okay now that we have man eating dogs out of the way back to the old Kook Kwick Canner.

Worth

Lol, no man eating dogs or dog eating people...

Worth1 · March 12, 2017

Monty will stand on his hind legs and paddle his feet together up and down.
He would have made a good circus dog.
Very smart.

I sent the pictuer to his owner she thought it was hilarious.
They are a young couple that live up the street.
She is also happy that he comes to my house to visit.
Sometimes he will stay with me all day.

Jimbotomateo · March 12, 2017

Quote:

Originally Posted by Worth1

Monty will stand on his hind legs and paddle his feet together up and down.
He would have made a good circus dog.
Very smart.

I sent the pictuer to his owner she thought it was hilarious.
They are a young couple that live up the street.
She is also happy that he comes to my house to visit.
Sometimes he will stay with me all day.

Worth, how long did it take Monty to clean up the casting on the Kwick Kook?

Worth1 · March 13, 2017

Quote:

Originally Posted by Jimbotomateo

Worth, how long did it take Monty to clean up the casting on the Kwick Kook?

About an hour.

Worth1 · March 13, 2017

Everything completed but the gasket.
All of the metal parts were de-rusted and boiled to neutralize anymore rust.
Including the screws.
Worth

Worth1 · March 14, 2017

I noticed moisture on the glass of my little KOOK Kwick canner gauge so I decided to take it apart and give it a cleaning and oiling.
This is why I like these old gauges they last forever if you know how to take them apart without breaking them.
This is also how you get into them to calibrate and set to zero.
Worth
IMG_20170313_10420.jpg

IMG_20170313_23586.jpg

IMG_20170313_41439.jpg

IMG_20170313_58211.jpg

AlittleSalt · March 14, 2017

Worth, looking at the pictures - is that Teflon tape on the threading? I strongly believe in Teflon tape on threaded plumbing. Just curious.

Worth1 · March 14, 2017

Yes it is Salt I use it and RectorSeal both.

I want to add the NEW gauge I bought is out of spec on the treads this ticks me off to no end.
It is national pipe thread but the diameter is cut a wee bit too small.

Worth

Worth1 · March 14, 2017

Today I took all of the gauges apart and cleaned them of all rust and polised them up.
Putting the one back together for the Kook Kwick I gave the cover just one last squeeze and cracked the glass face.
No big deal I will get another face.
The old gauge for the National is a geared gauge and very good quality.

The other day I called up the Auto supply store down the road from me and asked if they had a 1/8 NPT die to cut threads.
He came back and said they did.
I told the guy I would be there later to get one.
I was in line waiting because I couldn't find one on the rack.
I told the guy I called about a 1/8 pipe die.
Another guy tossed it down the counter and I bought it.
This isn't the first time they have done this for me.
Worth

Worth1 · March 15, 2017

Yes I did some experimentation and I found it.
I also found what I am 99% sure is the gasket replacement for the Kook Kwick 10-21 canner.
It is part number 09907.
I am almost sure of it.
It is a flat gasket and from all looking and reading it would fit this canner.
This gasket fits many of the old canners that use the same flat type rubber gasket.
Will I get one NO they are rubber from what I can tell, information is lacking.
There is also another one that should fit the smaller Kook Kwick 7-16 it is w906.

What I have done is experiment with some splicing tape this isn't regular tape.
I put it in the ring groove folded in half and lapped over by about 1/2 inch or so on the ends.
Pressured the canner up to 20 PSI and it held pressure.
One problem the tape is rated for only 198 degrees F.
I am not a fool I will not put this stuff under steam.
Not that I am worried about it blowing out as much as it becoming stuck in the groove and being hell to get out.

What I did find is silicone tape.
It is rated for 500 f and has about a 900 psi tinsel strength.
It will fuse to itself but not to anything else.

dmforcier · March 15, 2017

Intervention time?

Worth1 · March 16, 2017

The first attempt with the tape was a fiasco.
The second attempt with a different technique worked.
Here it is undergoing testing under steam.
Worth
IMG_20170316_14230.jpg

Worth1 · March 16, 2017

Folks I think we have a working canner no leaks what so ever.
It sure is nice to see this ole gal back up and running, it has been a lot of work.

As soon as it gets through with it's testing time trials I will see what my homemade gasket looks like.
It is supposed to be good to 500F.

Worth

Worth1 · March 16, 2017

Testing is completed no heat distortion or damage to the homemade silicone gasket at all.

Worth
IMG_20170316_29430.jpg

March 13, 2017	#201
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Everything completed but the gasket. All of the metal parts were de-rusted and boiled to neutralize anymore rust. Including the screws. Worth Last edited by Worth1; March 13, 2017 at 02:50 PM.

March 14, 2017	#204
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Yes it is Salt I use it and RectorSeal both. I want to add the NEW gauge I bought is out of spec on the treads this ticks me off to no end. It is national pipe thread but the diameter is cut a wee bit too small. Worth Last edited by Worth1; March 14, 2017 at 12:47 AM.

March 15, 2017	#206
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Eureka !!!!! Yes I did some experimentation and I found it. I also found what I am 99% sure is the gasket replacement for the Kook Kwick 10-21 canner. It is part number 09907. I am almost sure of it. It is a flat gasket and from all looking and reading it would fit this canner. This gasket fits many of the old canners that use the same flat type rubber gasket. Will I get one NO they are rubber from what I can tell, information is lacking. There is also another one that should fit the smaller Kook Kwick 7-16 it is w906. What I have done is experiment with some splicing tape this isn't regular tape. I put it in the ring groove folded in half and lapped over by about 1/2 inch or so on the ends. Pressured the canner up to 20 PSI and it held pressure. One problem the tape is rated for only 198 degrees F. I am not a fool I will not put this stuff under steam. Not that I am worried about it blowing out as much as it becoming stuck in the groove and being hell to get out. What I did find is silicone tape. It is rated for 500 f and has about a 900 psi tinsel strength. It will fuse to itself but not to anything else.

March 15, 2017	#207
dmforcier Tomatovillian™ Join Date: Apr 2016 Location: Dallas, TX Posts: 3,825	Intervention time? __________________ Stupidity got us into this mess. Why can't it get us out? - Will Rogers

March 12, 2017	#198
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Monty will stand on his hind legs and paddle his feet together up and down. He would have made a good circus dog. Very smart. I sent the pictuer to his owner she thought it was hilarious. They are a young couple that live up the street. She is also happy that he comes to my house to visit. Sometimes he will stay with me all day.

March 14, 2017	#202
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	I noticed moisture on the glass of my little KOOK Kwick canner gauge so I decided to take it apart and give it a cleaning and oiling. This is why I like these old gauges they last forever if you know how to take them apart without breaking them. This is also how you get into them to calibrate and set to zero. Worth IMG_20170313_10420.jpg IMG_20170313_23586.jpg IMG_20170313_41439.jpg IMG_20170313_58211.jpg

March 14, 2017	#203
AlittleSalt BANNED FOR LIFE Join Date: May 2014 Posts: 13,333	Worth, looking at the pictures - is that Teflon tape on the threading? I strongly believe in Teflon tape on threaded plumbing. Just curious.

March 14, 2017	#205
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Today I took all of the gauges apart and cleaned them of all rust and polised them up. Putting the one back together for the Kook Kwick I gave the cover just one last squeeze and cracked the glass face. No big deal I will get another face. The old gauge for the National is a geared gauge and very good quality. The other day I called up the Auto supply store down the road from me and asked if they had a 1/8 NPT die to cut threads. He came back and said they did. I told the guy I would be there later to get one. I was in line waiting because I couldn't find one on the rack. I told the guy I called about a 1/8 pipe die. Another guy tossed it down the counter and I bought it. This isn't the first time they have done this for me. Worth

March 16, 2017	#208
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	The first attempt with the tape was a fiasco. The second attempt with a different technique worked. Here it is undergoing testing under steam. Worth IMG_20170316_14230.jpg

March 16, 2017	#209
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Folks I think we have a working canner no leaks what so ever. It sure is nice to see this ole gal back up and running, it has been a lot of work. As soon as it gets through with it's testing time trials I will see what my homemade gasket looks like. It is supposed to be good to 500F. Worth

March 16, 2017	#210
Worth1 Tomatovillian™ Join Date: Feb 2006 Location: Den of Drunken Fools Posts: 38,539	Testing is completed no heat distortion or damage to the homemade silicone gasket at all. Worth IMG_20170316_29430.jpg