Tomatoville® Gardening Forums


Notices

New to growing your own tomatoes? This is the forum to learn the successful techniques used by seasoned tomato growers. Questions are welcome, too.

Reply
 
Thread Tools Display Modes
Old February 9, 2017   #1
JohnJones
Tomatovillian™
 
JohnJones's Avatar
 
Join Date: Mar 2015
Location: Mississippi
Posts: 339
Default I found this to be a simple, flexible & cheap grow light stand

http://gardenclub.homedepot.com/gard...s-light-stand/

Backing out the cost of the PVC cutter, which was $12, and not including the seed starting tray, etc. this setup cost me less than $25 and could be made larger with little extra expense. I found it to be a great idea for a beginning seed starter.

Last edited by JohnJones; February 9, 2017 at 04:27 AM. Reason: Grammer
JohnJones is offline   Reply With Quote
Old February 20, 2017   #2
Stampy
Tomatovillian™
 
Join Date: Jan 2017
Location: Niagara Region, Ontario
Posts: 14
Default

That's pretty much the same as the one I built, although I used 2" PVC and a 4' light. Simple project and pretty flexible for light height. Has served well all winter with lettuce, and herbs. Now in use for starting my seeds.
Stampy is offline   Reply With Quote
Old February 21, 2017   #3
JohnJones
Tomatovillian™
 
JohnJones's Avatar
 
Join Date: Mar 2015
Location: Mississippi
Posts: 339
Default

Quote:
Originally Posted by Stampy View Post
That's pretty much the same as the one I built, although I used 2" PVC and a 4' light. Simple project and pretty flexible for light height. Has served well all winter with lettuce, and herbs. Now in use for starting my seeds.
Yeah, I was thinking a larger gauge PVC would allow for a longer stand if I go bigger with my indoor effort at some point. I have added a couple of clamp lights to the sides to cover more area when needed.

Works well for me.
JohnJones is offline   Reply With Quote
Old April 10, 2017   #4
daylilydude
Tomatovillian™
 
daylilydude's Avatar
 
Join Date: May 2006
Location: Iuka, Mississippi Zone 7b
Posts: 482
Default

Mine is basically the same... just a double light that are 4ft.. Mine is made from left-over scrap 3/4 PVC I had left over from building a grow/green house.

__________________
Richard
daylilydude is offline   Reply With Quote
Old April 10, 2017   #5
Jimbotomateo
Tomatovillian™
 
Join Date: Jun 2016
Location: Santa Maria California
Posts: 1,014
Default

Quote:
Originally Posted by daylilydude View Post
Mine is basically the same... just a double light that are 4ft.. Mine is made from left-over scrap 3/4 PVC I had left over from building a grow/green house.

Where's that " like button". I need to push it! . Jimbo
Jimbotomateo is offline   Reply With Quote
Old April 10, 2017   #6
jtjmartin
Tomatovillian™
 
jtjmartin's Avatar
 
Join Date: May 2016
Location: Williamsburg VA Zone 7b
Posts: 1,110
Default

Dude:

What's the spacing between the PVC uprights?

I use a 3 shelf bookcase type set up with 4 feet shop lights but want to add a couple more lights that would sit like this on the garage floor. Great job.
jtjmartin is offline   Reply With Quote
Old April 11, 2017   #7
daylilydude
Tomatovillian™
 
daylilydude's Avatar
 
Join Date: May 2006
Location: Iuka, Mississippi Zone 7b
Posts: 482
Default

Quote:
Originally Posted by Jimbotomateo View Post
Where's that " like button". I need to push it! . Jimbo
Thank you...

Quote:
Originally Posted by jtjmartin View Post
Dude:

What's the spacing between the PVC uprights?

I use a 3 shelf bookcase type set up with 4 feet shop lights but want to add a couple more lights that would sit like this on the garage floor. Great job.
I cut the center bottom piece of pvc at 9 inches... hope this helps?
__________________
Richard
daylilydude is offline   Reply With Quote
Old April 11, 2017   #8
Worth1
Tomatovillian™
 
Worth1's Avatar
 
Join Date: Feb 2006
Location: Den of Drunken Fools
Posts: 38,539
Default

Just a thought.
If the tees on the bottom were bigger they could slip over the horizontal support on the floor.
This way they could slide back and forth.
I have no idea the dimensions right now.
Worth1 is offline   Reply With Quote
Old April 11, 2017   #9
Worth1
Tomatovillian™
 
Worth1's Avatar
 
Join Date: Feb 2006
Location: Den of Drunken Fools
Posts: 38,539
Default

I just went out and checked a 1x1x3/4 tee will slip right over 3/4 PVC.
This way there is no extra cutting of the bottom piece just to length is all.
With the machinery and tooling I have I could bore out the 3/4 fitting and it would sip back and forth.
In all reality I dont even need the fittings.
Worth
Worth1 is offline   Reply With Quote
Old April 11, 2017   #10
daylilydude
Tomatovillian™
 
daylilydude's Avatar
 
Join Date: May 2006
Location: Iuka, Mississippi Zone 7b
Posts: 482
Default

Quote:
Originally Posted by Worth1 View Post
I just went out and checked a 1x1x3/4 tee will slip right over 3/4 PVC.
This way there is no extra cutting of the bottom piece just to length is all.
With the machinery and tooling I have I could bore out the 3/4 fitting and it would sip back and forth.
In all reality I dont even need the fittings.
Worth

Thank you Worth, and I was just looking at a way to adjust the height and thought about a piece of 1/2in pvc that will slide into the uprights... split the uprights in half and drill some holes like an inch apart and use a small bolt and nut so you can raise and lower it as the seedlings grow... your thoughts??
__________________
Richard
daylilydude is offline   Reply With Quote
Old April 11, 2017   #11
Worth1
Tomatovillian™
 
Worth1's Avatar
 
Join Date: Feb 2006
Location: Den of Drunken Fools
Posts: 38,539
Default

Quote:
Originally Posted by daylilydude View Post
Thank you Worth, and I was just looking at a way to adjust the height and thought about a piece of 1/2in pvc that will slide into the uprights... split the uprights in half and drill some holes like an inch apart and use a small bolt and nut so you can raise and lower it as the seedlings grow... your thoughts??
I'll get with you tonight I on my phone at lunch at work.
Worth
Worth1 is offline   Reply With Quote
Old April 11, 2017   #12
daylilydude
Tomatovillian™
 
daylilydude's Avatar
 
Join Date: May 2006
Location: Iuka, Mississippi Zone 7b
Posts: 482
Default

AH-HA found one like I was thinking of... if I would have just googled it a lil more... LOL!

http://www.vegetablegardener.com/ite...ow-light-stand
__________________
Richard
daylilydude is offline   Reply With Quote
Old April 11, 2017   #13
Worth1
Tomatovillian™
 
Worth1's Avatar
 
Join Date: Feb 2006
Location: Den of Drunken Fools
Posts: 38,539
Default

Well that is not what I was thinking of.
I thought if two ways while I was working.

One would be to NOT drill all of those pesky holes.
Get a 10-24 tap drill holes in the fittings and thread them then use the 10-24 screws as set screws.
Two in each fitting.
An 8-32 screw might even be better or thumb screws.
Instead of a 90 at the top use a Tee.
This way you could have a long stick of PVC and just slide the Tee up and down.
You could even use a hose clamp if you wanted to.
Not to insult but if you or anyone else doesn't understand I can draw a picture.
I cannot express too much how everyone needs to have a screw pitch gauge.
I keep one in my pocket like a knife.

Worth
Worth1 is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:57 PM.


★ Tomatoville® is a registered trademark of Commerce Holdings, LLC ★ All Content ©2022 Commerce Holdings, LLC ★